Energyra® DynamIQ
When size and weight matters
Standard solar panels are heavy. Not in the least because of their thick glass sheet on the front. OK, let's rethink that! Energyra’s DynamIQ is a unique, lightweight solar panel. The innovative structure meets a variety of demands. A challenge for our researchers turned into an opportunity for all constructions that in the past were not designed for PV implementation.
Lightweight + power harvest
1 + 1 = 3!
Together with leading partners our unique, innovative front substrate has been developed with durable and protective properties. Main focus: reduce weight without compromising our premium quality.
Our PV technology turned out to be very beneficial for this. At the rear of the DynamIQ module we love our built-in, metallized environmental barrier. On top of that we developed a combination of hightech UV-stabilized material.
The result is an ultra light panel. Yet with unrivaled sturdiness, and still fully recyclable.
Just think about that!
The MWT back contact design marginalizes the effect of microcracks and hotspots to
an absolute minimum. In addition, the internal redundancy is optimally guaranteed with 61 active contacts per cell (3.660 at panel level). Especially when compared to the limited amount of busbars or wires on any traditional module.
Due to its low weight, the panel is easy to handle and can be used in locations where standard systems are not suitable. We love opening these new horizons!
Aesthetics is only one aspect. With the other ingredients it summs up to an ultra light panel. Yet with unrivaled sturdiness, and still fully recyclable.
Great benefits at a glance
MWT - PERC Solarcells
More net surface to generate power
Each solar cell converts sunlight into electricity. PERC monocrystalline cells are known for their broader spectral response, allowing them to generate lots of power in the early morning and late afternoon light as well. Combined with MWT (Multi Wrap Through) technology, the cells have a larger working surface that is exposed to the sun than conventional cells. Busbars are unnecessary. Above all: busbar-shading is completely ruled out!
~3%
More working surface
0.5%
More efficiency
Minimized micro-crack risk
More robust than conventional modules
Small cracks in solar cells are impossible to see with the bare eye, but can really impact the performance of a PV system. Most solar cells are composed of very thin silicon wafers, usually around 0.15 - 0.20 mm thick. Pressure or stress can induce micro-cracks. Newbies in the solar industry often unknowingly create micro-cracks by throwing boxes of gear on top of stacked panels or even balancing panels on their heads as they walk towards a ladder. Standing or kneeling on panels during installation is also a contributor to micro-cracks.
Energyra bank contact modules are more robust than conventional modules because of the integrated Conductive Backsheet (CBS). This innovative copper design ensures optimal contact with an incredible number of contact points across the entire cell. It acts as an additional (metal) environmental barrier to protect the cells and keep them sturdily in place, and actually strengthens the contacting architecture. If a micro-crack should occur, the cell will still be in perfect contact with the copper that conducts the energy, effectively designing the negative effects of microcracks out of the module.
Quality cells combined with high-quality European solar glass and sturdy frames makes Energyra modules virtually immune to micro-cracks in real-life conditions.
<2%
Degradation in year 1
0.4%
Degradation from year 2 and on...
Minimal 'Light Induced Degradation' (LID)
Significantly more yield over the entire lifespan
Due to technological advances in cell design and cell performance, LID impact on our DynamIQ modules is exceptionally low. So yield over the entire lifespan is significantly enhanced.
LID is the effect that occurs as soon as the panel is connected, the cells have to 'warm up' in the broad daylight for a bit before reaching the optimum yield.
<2%
Degradation in year 1
0.4%
Degradation from year 2 and on...
DynamIQ specifications
ELECTRICAL SPECIFICATIONS (STC, values for a 335'er)
| Energy yield per module | kWh/year | 342 |
|---|---|---|
| Max. power | Pmax (Wp) | 335 |
| Tolerance | Pn (Wp) | 0 / +3% |
| Open Circuit Voltage | Voc (V) | 40.8 |
| Short Circuit Current | Isc (A) | 10.6 |
| MPP Voltage | Vmpp (V) | 33.5 |
| MPP Current | Impp (A) | 10 |
| Module Efficiency | (%) | 19.9 |
| Maximum System Voltage | (V) | 1000 |
| Maximum Series Fuse Rating | (A) | 15 |
GENERAL SPECIFICATIONS
| Module Dimensions (L x W x H) | 1679mm x 1024mm x 33mm |
|---|---|
| Cell size | 162.75mm x 162.75mm; 60 cellen per module |
| Weight | 7,1 kg |
| Cell interconnect | Leadfree interconnect |
| Topsheet | Recycleable, dimensional and UV-stabilised PET |
| Cell type | Monocristalline silicon, PERC Metal Wrap Through (MWT) |
| Backsheet | Endurans climate barrier based on 100% recyclable high-grade PET. PFAS- and fluorine free. |
| Frame | Black anodised aluminium with slanted edges to minimise dirt built-up |
| Junction box | IP67, with 3 internal bypass diodes, double isolated 4 mm2 solar cable (1000 mm) and Stäubli MC-4 connectors |
CERTIFICATION
| IEC 61215 | Electrical Specifications | Connectors, cables, diodes, power, hotspots, irradiation, PID, hail, bypass, leakage current |
|---|---|---|
| IEC 61730 | Product safety | Temperature, humidity, UV, impulse voltage |
Other family-members
DeflectIQ
non-reflective:
no glare, no flare
Energrya is proud to present the first, dedicated developed, DeflectIQ panel. No AR-coating but real anti-reflex, fully deflective glass.
IconIQ
Full-black
IBC backcontact module
The IconIQ module is based on ZEBRA interdigitated back contact (IBC) cells, aimed at reducing production cost for high efficiency back contact technologies. The cells have been shown to reach over 24% in production
Availabity of DynamIQ
Our DynamIQ modules are distributed and supported by Energyra directly and over specialized partners worldwide.
Do you have specific questions or require industrial or mobile applications outside of the Benelux? Contacting Energyra is always a good idea!
